バージンPTFEと充填PTFE：自動車用シールではどちらが勝つか？

There is nothing worse than a call from a client saying a seal failed on the test bench three days before production start. The oil leak is messy, the shouting is loud, and the solution needs to happen yesterday.

If you are a material engineer in the automotive game, you know the drill. You’re looking at a standard PTFE seal and wondering, “Did I ask for the wrong stuff?”

The debate of Virgin vs. Filled PTFE isn’t just about color or cost. It’s about physics. It’s about how a material behaves when you smash it with 1,000 psi and spin a shaft against it at 5,000 RPM.

で テフロンX, we’ve seen enough melted, extruded, and shredded seals to know that “standard” specs usually don’t cut it. Today, I’m going to walk you through the nitty-gritty differences, strip away the marketing fluff, and look at the actual engineering data. We’ll figure out when you can get away with the pure stuff and when you absolutely need to bulk it up.

The Baseline: What is Virgin PTFE Actually Good For?

First off, let’s stop bashing Virgin PTFE. It’s an incredible material. It has that slippery, non-stick magic (coefficient of friction around 0.05 to 0.10) that makes it legendary.

Chemically? It’s a beast. You can throw almost any automotive fluid at it—ATF, brake fluid, ethanol blends—and Virgin PTFE just laughs. It doesn’t swell, it doesn’t dissolve.

But here’s the problem.

Virgin PTFE has the structural integrity of stiff cheese. I’m serious. It suffers badly from “Cold Flow” (creep). If you bolt a flange down on a Virgin PTFE gasket, come back in 24 hours. The bolts will be loose. Why? Because the material flowed away from the pressure.

The Weakness in Numbers

Let’s look at the tensile strength. Standard Virgin PTFE usually sits around:

• 抗張力： ~20-30 MPa
• 伸長： ~200-400%

Great for stretching, terrible for holding a tight tolerance under a heavy dynamic load. In an engine or transmission environment, pure PTFE wears out incredibly fast if there’s any rubbing. We call this the Specific Wear Rate (k).

For Virgin PTFE, the wear rate is astronomically high compared to filled grades. We are talking about a wear factor of roughly:
k ~ 500 x 10^-10 mm³/Nm

That’s… not good for a rotary shaft seal.

The Challenger: Filled PTFE (The “Muscle”)

So, how do we fix the soft cheese problem? We add fillers. Think of this like adding rebar to concrete. You keep the chemical resistance (mostly), but you skyrocket the mechanical strength.

When we talk about automotive seals comparison, we are usually looking at three main contenders to replace the virgin stuff:

1. Glass Filled PTFE
2. Carbon/Graphite Filled PTFE
3. Bronze Filled PTFE

Adding these fillers changes the game. You drop the deformation under load significantly.

The Physics of the Filler

Here is where it gets interesting. The filler takes the load. When the seal is pressed against a shaft, the PTFE acts as the lubricant, smearing a thin transfer film onto the metal, while the glass or bronze particles support the weight.

This increases the PV Limit (Pressure x Velocity).

• Virgin PTFE PV Limit: ~ 1,800 PSI-fpm
• Filled PTFE PV Limit: ~ 10,000+ PSI-fpm

That is a massive difference. If your application involves high RPMs, Virgin PTFE isn’t even in the race.

Deep Dive: Comparing the Specifics

Let’s break this down by the properties that actually matter to you when you’re designing a seal.

1. Wear Resistance and Tribology

This is usually the #1 reason engineers switch to our PTFEガスケット and seals made with fillers.

The formula for wear volume (W) is generally expressed as:
W = k * F * L
どこでだ：

• W = Wear volume (mm³)
• k = Specific wear rate (mm³/Nm)
• F = Normal force (N)
• L = Sliding distance (m)

If you use glass filled PTFE, the ‘k’ value drops dramatically.

• Virgin ‘k’: ~500
• 25% Glass Filled ‘k’: ~2 – 5

You are looking at a material that lasts 100x longer in sliding contact. However, there’s a catch. Glass is abrasive. If you use glass-filled PTFE on a soft shaft (like unhardened aluminum or mild steel), the seal won’t wear out, but the shaft will.

I’ve seen customers destroy a $500 shaft to save $2 on a seal. Don’t be that guy.

2. Creep and Deformation

In automotive applications, temperatures fluctuate wildy. -40°C in winter to 150°C under the hood. Virgin PTFE has a high coefficient of thermal expansion and low creep resistance.

Deformation under load (14 MPa @ 23°C for 24 hrs):

• Virgin: ~15% deformation
• 25% Glass Filled: ~11% deformation
• Bronze Filled: ~7% deformation

If you need the seal to maintain geometry under clamping force, you gotta go filled.

3. Thermal Conductivity

Heat kills seals. Virgin PTFE is a thermal insulator. It traps heat at the sealing interface. This leads to carbonization of the oil or melting of the seal lip.

Carbon filled PTFE is the hero here. It conducts heat away from the contact point.

• Virgin: ~0.25 W/mK
• Carbon Filled: ~0.60+ W/mK

If you have a high-speed rotary application (like a crank seal), moving that heat away is critical.

Specific Fillers: Choosing Your Fighter

Okay, so you know you need filled. But which one? Here is the cheat sheet I use at テフロンX when consulting.

Glass Fiber (The All-Rounder)

Usually 15% or 25% glass fiber.

• Pros: High compressive strength, excellent wear resistance, chemically inert (except to hydrofluoric acid).
• 短所だ： Abrasive to mating surfaces. Can increase porosity.
• Best for: Static seals, valve seats, gaskets where rotation is slow or the mating metal is hard (Rockwell C 45+).

Carbon / Graphite (The Slick Operator)

• Pros: Self-lubricating, low friction, excellent thermal conductivity. Soft enough not to damage shafts.
• 短所だ： More expensive than glass. Black color limits visual inspection for cleanliness in some niche apps (rare in auto).
• Best for: High-speed rotary seals, shock absorbers, piston rings.

Bronze (The Heavy Lifter)

• Pros: Highest compressive strength, best thermal conductivity.
• 短所だ： Attacked by acids/alkalis (chemical resistance drops), expensive.
• Best for: Hydraulic systems, extrusion resistance, heavy-duty transmission seals.

Real World Scenario: The “Leaky” Transmission Case

Let me tell you about a project we handled last year. Let’s call the client “AutoCorp.”

They were designing a new DCT (Dual Clutch Transmission). They specced Virgin PTFE for the internal control piston seals because they wanted lowest possible friction for fast shifting.

The Failure:
During the 100-hour durability test, the shifting got sloppy. Eventually, the pressure dropped, and the transmission failed.

The Diagnosis:
We pulled the seals. They looked like pancakes. The heat generated by the rapid actuation, combined with the hydraulic pressure, caused the Virgin PTFE to cold flow. The seal lip flattened out, loss of contact pressure -> leak.

修正
We switched them to a custom 15% Glass + 5% MoS2 filled PTFE.

1. Glass stopped the cold flow.
2. MoS2 (Molybdenum Disulfide) lowered the friction coefficient back down near Virgin levels.

Result? Passed the 500-hour test with zero leakage. Sometimes you have to mix and match. If you have a tricky application like this, shoot an email to アリソン・イェ@teflonx.com. We love solving these puzzles.

Quick Comparison Table

I know engineers love tables. Here is the snapshot.

財産	バージンPTFE	Glass Filled PTFE	Carbon Filled PTFE	Bronze Filled PTFE
色	白	Off-White / Gray	Black	Brown / Bronze
Friction Coeff.	Excellent (0.05)	Good (0.15)	Excellent (0.10)	Fair (0.20)
耐摩耗性	貧しい	素晴らしい	非常に良い	素晴らしい
Shaft Wear	低い	High (Abrasive)	低い	Low-Medium
クリープ抵抗	低い	中くらい	中くらい	高い
Thermal Cond.	低い	低い	高い	非常に高い
料金	$	$$	$$$	$$$

Cost vs. Performance: The Trade-off

Look, I get it. Procurement is breathing down your neck to cut costs. Virgin PTFE is cheaper.

But calculating cost based on the price per gram of material is a trap. You need to calculate the Cost of Failure.

If a $0.50 Virgin seal fails and causes a warranty claim on a $2,000 transmission, that math doesn’t work out.

However, don’t over-engineer if you don’t have to. If you are designing a static dust boot or a cap that sees no load and no friction, Virgin PTFE is perfect. It looks clean, it’s cheap, and it works.

But for automotive seals comparison in dynamic environments (crankshafts, cam shafts, transmission pistons, suspension struts), the filled grades pay for themselves by surviving the warranty period.

A Note on Surface Finish

This is something people forget. If you switch from Virgin to Filled, you might need to adjust your shaft surface finish.

• バージンPTFE: Likes a very smooth finish (Ra 0.2 – 0.4 µm).
• 充填PTFE: Can actually benefit from a slightly rougher finish (Ra 0.4 – 0.8 µm) to help establish that transfer film I mentioned earlier.

If the shaft is too smooth, the filled PTFE might just slide over it without depositing the transfer film, leading to higher friction and heat. It’s a delicate balance.

Wrapping It Up

Choosing between Virgin vs. Filled PTFE isn’t about which material is “better.” It’s about matching the material to the abuse it’s going to take.

• 使用 Virgin for static, chemical-heavy, low-load spots.
• 使用 Glass Filled for general wear resistance and heavy loads (watch the shaft hardness!).
• 使用 Carbon/Bronze for high heat and high pressure.

Don’t guess. The wrong choice leaks.

If you are staring at a CAD drawing right now wondering which compound to specify, stop guessing. We have the data, and we have the materials. Check out our range of PTFEガスケット to see what’s possible.

Or, just skip the browsing and ask us directly. We can run the PV calculations for you.
Contact us here: https://teflonx.com/contact-us/
メールアドレス: アリソン・イェ@teflonx.com

Let’s make sure your seals actually seal.

---

FAQ: Common Questions on PTFE Seals